JetPaste v.1.1 JetPaste is a utility for storing and pasting commonly used text phrases or formatted text into the applications.HotKeyz v.2.2.1 HotKeyz is a keyboard utility with hotkey / shortcut control for executing files, folders, Start / Run commands, opening your mail, browsing to a website and logging in and much more.4153 is the radial centre line of the railing. Hence the rise of 473.3 was also across those three risers. You can also see the helical line I forgot to delete that I was attempting to use as a path along the top centre of the railing.įYI the 10.93° was the angle from post to post, equivalent to three tread nosings. (geometry courses have a purpose) The result is the pink profile embedded over the profile that the stair tool created. I eventually used the standard sweep tool. I calculated manually what the height of the profile would be when sliced at the angle of the stair's incline along the radial centre line of the railing's location. I reminds me of the angle a person might be traveling at while riding a water slide due to centrifugal force. The middle profile is what the tool produced without corrections. The top most was the closest to being correct where I had rotated the rectangle 45° in an attempt to plumb the profile's sides. You can see two of my efforts in the picture. This behaviour might be limited to shortcuts where a modifier key is not required.Īs mentioned I couldn't utilize the helix line as a path for my rectangular profile due to some rotational issue that I don't quite comprehend. The menu system does not respond to changes while the object info palette is active.
CLOUDCLIP PASTE HOTKEY PC
Every time you modify something in the Object Info Palette on a PC you need to press or click in the main window before the other keyboard shortcuts become available. One might (?) be able to assign some thumb buttons to act as modifier keys and definitely the key. The placement of and on most PC keyboards makes it next to impossible to use many frequent short-cuts with one hand without incurring repetitive stress injury from stretching one's fingers too far apart.
CLOUDCLIP PASTE HOTKEY PLUS
The large ergonomics of the Death Adder have been a big plus for me and assigning the thumb buttons to switch sheets/layers a feature that I could not imagine doing without anymore, whether it be on a PC or a Mac.īut I will say that one of the Naga's will be worth testing out, especially if you are considering operating from a PC.
CLOUDCLIP PASTE HOTKEY SOFTWARE
But the Synapse 2 software required for the Mac could not find the new budget version of DeathAdder. When I received a new Death Adder to go with the new company issued PC I was going to let it go to the Jr Tech who was to work on my former Mac workstation and retain my old (dirty) DeathAdder for myself. If deciding upon a Razer product your selection will need to be recognized by their synapse 2 software to work on the Mac. If you save and revert to saved you will probably be able to get the centre snap points to appear again but it will not be long before this functionality starts to fail again. (adjust clip boundary first if necessary to see all six rectangles)Īttempt to dimension from any corner to any circle's centre. Go back to the sheet and edit annotation. Select both originals again, duplicate and create symbol. Select both rectangles, duplicate and group. Next exit annotation change layer to design layer. Now edit annotation and you should be able to place a dimension from any corner of the object to a centre of one or more of the circles. On a sheet layer create a viewport to said design layer at say 1:4 scale to encompass both rectangles. Select both and subtract circles from rectangle.
Lower extruded circles by 1mm below unpunched rectangle. Paste in place original rectangle and extrude it 6mm. Move punched rectangle to one side and extrude 6mm. Select rectangle and circles and clip surface. Create four circles in various locations inside the rectangle. On a design layer, create a rectangle centred upon 0,0. This is most prevalent with extrudes, grouped objects and symbol objects but can occur in other situations. Issue: When dimensioning in the annotation space of view ports, the snap location to a hole's centre does not always appear.
0 kommentar(er)
